|All Land Pride Cutters have been designed and tested and meet rigorous voluntary
testing procedures specified by ANSI.
||Saves customer set-up time and money.
|Fully welded deck
||Fully welded deck adds strength.
|250 HP Divider gearbox
210 HP center & wing gearboxes
|A rugged heavy built gearboxes capable of handling heavy cutting applications.
|Gearbox seal protection
||Gearbox bottom seal protection for longer bearing life.
Cat. 6 CV or Cat. 5 Conventional
|Holds up to shock loads and harsh mowing conditions.
Fits wide range of tractors including high horsepower tractors.
|Star profile drivelines
||Star profile spreads load out to many points on the shaft. More apt to resist bending and
twisting under shock loads and harsh mowing conditions.
|Easy greasable drivelines
||Drivelines have access holes for greasing the U-joints and to grease the inner profiles.
|4 Plate slip-clutch
||Protects drivelines and gearboxes by slipping clutches rather than twisting the driveline
when impacts are encountered.
|High blade tip speed
||540 rpm: Center: 17,377 fpm, Wings: 17,329 fpm
1000 rpm: Center: 18,165 fpm, Wings: 15,013 fpm
Allows for a clean cut of material and even distribution.
|6" Blade overlap
||Generous blade overlap eliminates skipping, especially in turns.
|High cutting capacity
||Can cut brushy areas with saplings up to 3".
|Left wing rotates counterclockwise
||Better discharge of material. Picks up tractor tracks.
|10 1/2" Deck height
||Handles heavy cutting, which reduces balling-up of cut material under the deck.
|3/16" Stump jumper backed with a
1" thick mounting bar
|Heavy round stump jumper with bottom gearbox seal protector. Can hold up to tough
|3/16" Deck thickness
||Heavy enough to handle conditions but not weigh unit down.
|Self-leveling pull-type hitch
||Reduces drawbar wear by keeping hitch level while going through ditches.
|LED Signal lights
||LED lights are bright, long lasting, and resistant to vibration, unlike incandescent
|Hinged wing sections
||Allow cutter to follow terrain. Ideal for rough ground where hillsides, ditches, and
hollows can cause uneven cutting.
|1" Solid hinge rods
||Larger diameter hinge rod gives greater strength to the cutter from front to rear, and in
the hinge area itself.
|Wing transport locks
||Safety feature. Holds wing sections up in case of hydraulic pressure loss.
|Enclosed front to rear dual leveling
|Dual leveling rods enable the cutter to pull equally on the rear axle during travel over
rough terrain. Many competitors only use one leveling rod.
|Drain holes in wheel rims
||Allows water to drain from wheels mounted on the folded-up wings.
Helps prevent paint deterioration and rusting to the wheel rims.
|5" Square rear axle tubing
||Heavy axle to handle harsh conditions.
||Protects unit from bumps and ground shock.
|Replaceable wheel spindles
||Wheel spindles can be replaced when damaged without replacing the entire axle.
Simply remove two bolts to replace damaged spindle.
|Double swivel hitch
||Great for uneven terrain, reduces drawbar wear.
||Ideal for extreme conditions. Clamps tight to drawbar eliminating drawbar wear.
||Laminated tires: Eliminates flats.
Airplane tires without foam filling: Give better cushion while transporting.
Airplane tires with foam filling: Give better cushion while transporting and can’t go
|Deck rings (optional)
||1/2" x 3" full welded deck ring keeps blades from damaging the deck.
|Shredder Blades (Optional)
||Ideal for cutting residue into smaller pieces.
Replaces blade and stump jumper configuration.
||Maintains shredded material in each section of the cutter for a consistent discharge
from the rear of each deck.